Описание материалов:
Production-Grade Thermoplastic for Dimension 3D Printers
ABSplus is a true production-grade thermoplastic that is durable enough to perform virtually the same as production parts. When combined with Dimension 3D Printers, ABSplus is the ideal solution to printing 3D models in an office environment.
| Главная Информация | |
|---|
| Характеристики | |
| Используется | |
| Номер файла UL | |
| Внешний вид | - Черный
- Синий
- Темно-зеленый
- Темно-серый
- Слоновая кость
- Оранжевый
- Красный
- Белый
- Желтый
|
| Метод обработки | - 3D печать, Плавленая нить (FFF)
|
| Физический | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Удельный вес | 1.04 | g/cm³ | ASTM D792 |
| Толщина-
Возможность слоя | 177.8 to 330.2 | µm | |
| Механические | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Флекторное расслоение | 31.0 | MPa | ASTM D790 |
| Электрический | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Сопротивление громкости 1 | 6.0E+13 to 3.0E+14 | ohms | ASTM D257 |
| Механические | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Модуль растяжения 2(3.18 mm) | 2280 | MPa | ASTM D638 |
| Прочность на растяжение 3(3.18 mm) | 36.5 | MPa | ASTM D638 |
| Удлинение при растяжении 4(Break, 3.18 mm) | 3.0 | % | ASTM D638 |
| Флекторный модуль 5 | 2210 | MPa | ASTM D790 |
| Flexural Strength 6 | 52.4 | MPa | ASTM D790 |
| Воздействие | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Зубчатый изод Impact (23°C) | 110 | J/m | ASTM D256A |
| Тепловой | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Температура отклонения при нагрузке | | | ASTM D648 |
| 0.45 MPa, Unannealed | 95.6 | °C | |
| 1.8 MPa, Unannealed | 82.2 | °C | |
| Температура перехода стекла | 108 | °C | DMA |
| CLTE-
Поток | 8.8E-5 | cm/cm/°C | ASTM E831 |
| Электрический | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Диэлектрическая прочность 7 | | | |
| -- 8 | 0.10 to 0.32 | kV/mm | ASTM D149 |
| -- | 28 | kV/mm | IEC 60112 |
| Диэлектрическая постоянная 9 | 2.60 to 2.90 | | ASTM D150 |
| Коэффициент рассеивания 10 | 4.6E-3 to 5.3E-3 | | ASTM D150 |
| Воспламеняемость | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Огнестойкость (2.29 mm) | HB | | UL 94 |
| Примечание |
|---|
| 1 . | All Electrical Property values were generated from the average of test plaques built with default part density (sparse). Test plaques were 4.0 x 4.0 x 0.1 inches (102 x 102 x 2.5 mm) and were built both in the flat and vertical orientation. The range of values is mostly the result of the difference in properties of test plaques built in the flat vs. vertical orientation. |
| 2 . | Type I, 5.1 mm/min |
| 3 . | Type I, 5.1 mm/min |
| 4 . | Type I, 5.1 mm/min |
| 5 . | Method I (3 point load), 1.3 mm/min |
| 6 . | Method I (3 point load), 1.3 mm/min |
| 7 . | All Electrical Property values were generated from the average of test plaques built with default part density (sparse). Test plaques were 4.0 x 4.0 x 0.1 inches (102 x 102 x 2.5 mm) and were built both in the flat and vertical orientation. The range of values is mostly the result of the difference in properties of test plaques built in the flat vs. vertical orientation. |
| 8 . | Method A (Short-Time) |
| 9 . | All Electrical Property values were generated from the average of test plaques built with default part density (sparse). Test plaques were 4.0 x 4.0 x 0.1 inches (102 x 102 x 2.5 mm) and were built both in the flat and vertical orientation. The range of values is mostly the result of the difference in properties of test plaques built in the flat vs. vertical orientation. |
| 10 . | All Electrical Property values were generated from the average of test plaques built with default part density (sparse). Test plaques were 4.0 x 4.0 x 0.1 inches (102 x 102 x 2.5 mm) and were built both in the flat and vertical orientation. The range of values is mostly the result of the difference in properties of test plaques built in the flat vs. vertical orientation. |
