- Главная страница
- Поиск продуктов
- PBT
- Ranger PBT PBT-403-M-G20
Ranger PBT PBT-403-M-G20
| Категория | PBT, Polybutylene Terephthalate |
| Производитель | Beijing Ranger Chemical Co., Ltd. |
| Торговая марка | Ranger PBT |
| Порт | Китай Шанхайский порт |
| Торговые условия | FOB, CFR, CIF |
| Платежное средство | L/C, T/T, Western Union |
WS8gmo_Ranger-PBT-PBT-403-M-G20.pdf  |
|
| Контактная информация |  Служба поддержки клиентов Вичат |
|
|
|
Описание материалов:
Unreinforced grades have abundant strength and flexibility, and have strong characteristics against brittleness.
UL-certified slow-burning(94HB) and self-extinguishing grades(94V-0,V-2) exist, and electrical properties exhibited are the highest of any thermoplastic.
Low water absorption is exhibited, and excellent electrical properties(CTI and GWIT) are retained over extended periods of usages, even with widely varied temperature and humidity conditions.
The surface of molded products is smooth, and a low coefficient of friction is exhibited.As the amount of froction is low, PBT is suitable for use in application requiring friction and wear properties.
The material is exceptionally reliable, with small in-use dimensional variation, and superior molding stability and dimensional precision.
Long-term chemical resistance is exceptional, and at room temperature, there is almost no degradation in properties after.
Both unreinforced and reinforced grades exhibit exceptional flowability, and excellent processability.
Application:VCD drive frames\ Connectors\ Trimmers\ Switch buttons for gas-fired instantaneous water heaters\ Relay blocks\ Driers\ Rectifiers\ Outer handles\ Height sensor cases\ Door mirror stays\ Drive component housings\ Energy saving lamp.
UL-certified slow-burning(94HB) and self-extinguishing grades(94V-0,V-2) exist, and electrical properties exhibited are the highest of any thermoplastic.
Low water absorption is exhibited, and excellent electrical properties(CTI and GWIT) are retained over extended periods of usages, even with widely varied temperature and humidity conditions.
The surface of molded products is smooth, and a low coefficient of friction is exhibited.As the amount of froction is low, PBT is suitable for use in application requiring friction and wear properties.
The material is exceptionally reliable, with small in-use dimensional variation, and superior molding stability and dimensional precision.
Long-term chemical resistance is exceptional, and at room temperature, there is almost no degradation in properties after.
Both unreinforced and reinforced grades exhibit exceptional flowability, and excellent processability.
Application:VCD drive frames\ Connectors\ Trimmers\ Switch buttons for gas-fired instantaneous water heaters\ Relay blocks\ Driers\ Rectifiers\ Outer handles\ Height sensor cases\ Door mirror stays\ Drive component housings\ Energy saving lamp.
| Главная Информация | |
|---|---|
| Характеристики |
|
| Используется |
|
| Формы |
|
| Метод обработки |
|
| Физический | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Удельный вес | 1.56 | g/cm³ | ASTM D792 |
| Формовочная усадка- Поток | 0.40 - 0.70 | % | ASTM D955 |
| Поглощение воды (23°C, 24 hr) | 0.050 | % | ASTM D570 |
| Механические | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Прочность на растяжение (Yield) | 115 | MPa | ASTM D638 |
| Флекторный модуль | 8000 | MPa | ASTM D790 |
| Flexural Strength | 180 | MPa | ASTM D790 |
| Воздействие | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Зубчатый изод Impact | 10 | kJ/m² | ASTM D256 |
| Незубчатый изод ударная прочность | 60 | kJ/m² | ASTM D256 |
| Тепловой | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Температура отклонения при нагрузке | ASTM D648 | ||
| 0.45 MPa, not annealed | 220 | °C | ASTM D648 |
| 1.8 MPa, not annealed | 205 | °C | ASTM D648 |
| Электрический | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Сопротивление громкости (2.00 mm) | 1.2E+16 | ohms·cm | ASTM D257 |
| Диэлектрическая прочность (2.00 mm) | 20 | kV/mm | ASTM D149 |
| Диэлектрическая постоянная (50 Hz) | 3.20 | ASTM D150 | |
| Коэффициент рассеивания (50 Hz) | 0.020 | ASTM D150 |
| Воспламеняемость | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Огнестойкость | UL 94 | ||
| 0.800 mm | V-0 | UL 94 | |
| 1.60 mm | V-0 | UL 94 |
| Инъекция | Номинальное значение | Единица измерения | |
|---|---|---|---|
| Задняя температура | 225 - 250 | °C | |
| Средняя температура | 225 - 250 | °C | |
| Передняя температура | 225 - 250 | °C | |
| Температура сопла | 240 | °C | |
| Температура формы | 60.0 - 80.0 | °C | |
| Давление впрыска | 60.0 - 120 | MPa | |
| Back Pressure | 6.00 - 18.0 | MPa | |
| Screw Speed | < 100 | rpm |
| Инструкции по впрыску |
|---|
| Injection Time: 3 to 15 secTime Pressure: 2 to 5 secTotal Cycle: 15 to 50 sec |
| Тип материала | Категория | Производитель |
|---|---|---|
| OP - PBT 25GB-5GF-IM | PBT | Oxford Polymers |
| SPESIN® KP212G30V0LG | PBT | Kolon Plastics, Inc. |
| Wondel® T TG3 | PBT | Nanjing Julong Engineering Plastics Co., LTD |
| Yuyao PBT 3058G30 | PBT | Yuyao Tenglong Plastics Co., Ltd. |
| Anjaflam® 450-FR/GF30 | PBT | Almaak International GmbH |
| NOVADURAN® 5010G45 | PBT | Mitsubishi Engineering-Plastics Corp |
Получите информацию об этом продукте следующим способом.
| Телефон | +086 13424755533 |
| EMAIL US | sales@su-jiao.com |
Служба поддержки клиентов Вичат | |
Copyright © russianpolymer.com All Rights Reserved