- Главная страница
- Поиск продуктов
- PPSU
- Radel® R-7700
Radel® R-7700
| Категория | PPSU, Polyphenylsulfone |
| Производитель | Solvay Specialty Polymers |
| Торговая марка | Radel® |
| Порт | Китай Шанхайский порт |
| Торговые условия | FOB, CFR, CIF |
| Платежное средство | L/C, T/T, Western Union |
zY6yHh_Radel-R-7700.pdf  |
|
| Контактная информация |  Служба поддержки клиентов Вичат |
|
|
|
Описание материалов:
Radel® R-7700 polyphenylsulfone sheet was developed specifically for aircraft interior applications. Through the use of a proprietary flame retardant package, this resin offers low heat release, low smoke generation and low toxic gas emissions, thereby complying with the FAA regulation 14CFR Part 25.853 Appendix F. In addition, it has excellent impact resistance and meets typical industry requirements for resistance to aerospace fluids, even under stress.
Radel® R-7700 is available in pellets and sheet form.
Radel® R-7700 sheet can be formed into large complex geometries with relative ease on conventional thermoforming equipment. Please reference the Technical Bulletin Thermoforming Radel® R-7700 Sheet for additional information.
Radel® R-7700 is available in pellets and sheet form.
Radel® R-7700 sheet can be formed into large complex geometries with relative ease on conventional thermoforming equipment. Please reference the Technical Bulletin Thermoforming Radel® R-7700 Sheet for additional information.
- Available in several custom colors
| Главная Информация | |
|---|---|
| Характеристики |
|
| Используется |
|
| Рейтинг агентства |
|
| Соответствие RoHS |
|
| Внешний вид |
|
| Формы |
|
| Метод обработки |
|
| Физический | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Удельный вес | 1.34 - 1.42 | g/cm³ | ASTM D792 |
| Поглощение воды (24 hr) | 0.35 | % | ASTM D570 |
| Механические | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Модуль растяжения (3.18 mm) | 2280 | MPa | ASTM D638 |
| Прочность на растяжение (3.18 mm) | 58.6 | MPa | ASTM D638 |
| Удлинение при растяжении (Break, 3.18 mm) | 15 | % | ASTM D638 |
| Флекторный модуль (3.18 mm) | 2340 | MPa | ASTM D790 |
| Flexural Strength (3.18 mm) | 100 | MPa | ASTM D790 |
| Воздействие | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Зубчатый изод Impact (3.18 mm) | 130 | J/m | ASTM D256 |
| Незубчатый изод Impact (3.18 mm) | No Break | ASTM D256 | |
| Ударное падение Dart (3.18 mm) | > 31.1 | J | BS 7271 |
| Тепловой | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Температура отклонения при нагрузке (1.8 MPa, Unannealed, 3.18 mm) | 202 | °C | ASTM D648 |
| Воспламеняемость | Номинальное значение | Единица измерения | Метод испытания |
|---|---|---|---|
| Выброс токсичного газа | |||
| Nitrogen gas At 4 minutes 1 | ppm | ||
| Hydrogen fluoride 2 | ppm | ||
| Sulfur oxide, 4 minutes 3 | 3 | ppm | |
| Hydrogen chloride 4 | ppm | ||
| Hydrogen cyanide, 4 minutes 5 | ppm | ||
| Carbon monoxide, 4 minutes 6 | 40 | ppm | |
| Exothermic | Ohio State University | ||
| 2 minutes : 1.52 to 3.18mm 7 | kW·min/m² | Ohio State University | |
| Peak rate : 1.52 to 3.18mm 8 | kW/m² | Ohio State University | |
| Плотность Дыма | ASTM F814 | ||
| specific optical density, at 1.5 minutes 9 | 1.0 | Ds | ASTM F814 |
| Maximum specific optical density, at 4 minutes 10 | 3.0 | Ds | ASTM F814 |
| Дополнительная информация |
|---|
| The Federal Aviation Admininstration (FAA) has issued stringent regulations covering materials for use in commercial aircraft interiors. As shown in the Heat Release and Smoke Density data above, Radel R-7700 sheet complies with these regulations.In addition, several airframe manufacturers have an additional requirement that, when these materials burn, any smoke generated contain no more than defined levels of specific toxic gases. Radel R-7700 polyphenylsulfone sheet typically exhibits levels of these gases that are much lower than the maximum levels allowed, see Toxic Gas Emission data above. |
| Примечание | |
|---|---|
| 1 . | Combustion mode; BMS specification limit = 60 ppm; ATS 1000.001 specification limit = 100 ppm |
| 2 . | Combustion mode; BMS specification limit = 60 ppm;ATS 1000.001 specification limit = 50 ppm |
| 3 . | Combustion mode: BMS specification limit = 30 ppm; ATS 1000.001 specification limit = 100 ppm |
| 4 . | Combustion mode; BMS specification limit = 60 ppm; ATS 1000.001 specification limit = 500 ppm |
| 5 . | Combustion mode; BMS specification limit = 60 ppm; ATS 1000.001 specification limit = 150 ppm |
| 6 . | Combustion mode: BMS specification limit = 500 ppm;ATS 1000.001 specification limit = 3500 ppm |
| 7 . | FAA requirements, 14CFR PART 25.853 Appendix F: 65 KW-min/m² |
| 8 . | FAA requirements, 14CFR PART 25.853 Appendix F: 65 KW/m² |
| 9 . | Burning mode |
| 10 . | Burning mode; FAA industry requirements: 200 |
| Тип материала | Категория | Производитель |
|---|---|---|
| RTP 1499 P X 102560 A | PPSU | RTP Company |
| RTP 1400 R-5100 | PPSU | RTP Company |
| Quadrant EPP PPSU 1000 | PPSU | Quadrant Engineering Plastic Products |
| EUROPLEX® Film HPF 99211 | PPSU | Evonik Industries AG |
| LUVOCOM® 1502-8752 | PPSU | Lehmann & Voss & Co. |
| RTP 1499 P X 125056 B | PPSU | RTP Company |
Получите информацию об этом продукте следующим способом.
| Телефон | +086 13424755533 |
| EMAIL US | sales@su-jiao.com |
Служба поддержки клиентов Вичат | |
Copyright © russianpolymer.com All Rights Reserved