Описание материалов:
Chemlon® E-6 GF15 is an economy range 15% glass fibre reinforced Nylon 6 compound.
It is available in natural or black versions.
| Главная Информация | |
|---|
| Наполнитель/армирование | - Армированный стекловолокном материал, 15% наполнитель по весу
|
| Внешний вид | |
| Метод обработки | |
| Физический | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Плотность | 1.24 | g/cm³ | ISO 1183 |
| Формовочная усадка 1 | 0.60 - 1.0 | % | Internal method |
| Поглощение воды (Equilibrium, 23°C, 50% RH) | 2.3 | % | ISO 62 |
| Механические | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Модуль растяжения | 5500 | MPa | ISO 527-2 |
| Tensile Stress (Break) | 105 | MPa | ISO 527-2 |
| Растяжимое напряжение (Break) | 3.0 | % | ISO 527-2 |
| Флекторный модуль | 5000 | MPa | ISO 178 |
| Флекторный стресс 2 | 150 | MPa | ISO 178 |
| Воздействие | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Зубчатый изод Impact | 5.0 | kJ/m² | ISO 180 |
| Тепловой | Номинальное значение | Единица измерения | Метод испытания |
|---|
| Heat Deflection Temperature | | | |
| 0.45 MPa, not annealed | > 190 | °C | ISO 75-2/B |
| 1.8 MPa, not annealed | 175 | °C | ISO 75-2/A |
| Инъекция | Номинальное значение | Единица измерения | |
|---|
| Температура сушки | 80.0 | °C | |
| Время сушки | 2.0 | hr | |
| Задняя температура | 230 - 260 | °C | |
| Средняя температура | 230 - 260 | °C | |
| Передняя температура | 230 - 260 | °C | |
| Температура обработки (расплава) | < 300 | °C | |
| Температура формы | 80.0 - 90.0 | °C | |
| Скорость впрыска | Fast | | |
| Screw Speed | 50 - 200 | rpm | |
| Инструкции по впрыску |
|---|
| Back pressure: LowInjection pressure: HighThe material is supplied dry and ready to mould in sealed, moisture proof sacks. No drying is necessary unless the material has been exposed to air for longer than three hours. The appearance of splash marks on the surface of mouldings indicates excessive moisture is present. Should drying become necessary, two hours at 80°C in a dehumidifying drier is recommended. The use of air circulating driers is not generally recommended, as longer drying times are often required, with greater potential for product oxidation and yellowing. Drying temperatures should not exceed 80°C. |
| Примечание |
|---|
| 1 . | Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions.The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding). |
| 2 . | At Break |
